794 lines
20 KiB
C
794 lines
20 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
// Copyright (c) 2024-2025 Linaro Ltd
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/units.h>
|
|
#include <media/v4l2-cci.h>
|
|
#include <media/v4l2-ctrls.h>
|
|
#include <media/v4l2-device.h>
|
|
#include <media/v4l2-fwnode.h>
|
|
|
|
#define OV6211_LINK_FREQ_480MHZ (480 * HZ_PER_MHZ)
|
|
#define OV6211_MCLK_FREQ_24MHZ (24 * HZ_PER_MHZ)
|
|
|
|
#define OV6211_REG_CHIP_ID CCI_REG16(0x300a)
|
|
#define OV6211_CHIP_ID 0x6710
|
|
|
|
#define OV6211_REG_MODE_SELECT CCI_REG8(0x0100)
|
|
#define OV6211_MODE_STANDBY 0x00
|
|
#define OV6211_MODE_STREAMING BIT(0)
|
|
|
|
#define OV6211_REG_SOFTWARE_RST CCI_REG8(0x0103)
|
|
#define OV6211_SOFTWARE_RST BIT(0)
|
|
|
|
/* Exposure controls from sensor */
|
|
#define OV6211_REG_EXPOSURE CCI_REG24(0x3500)
|
|
#define OV6211_EXPOSURE_MIN 1
|
|
#define OV6211_EXPOSURE_MAX_MARGIN 4
|
|
#define OV6211_EXPOSURE_STEP 1
|
|
#define OV6211_EXPOSURE_DEFAULT 210
|
|
|
|
/* Analogue gain controls from sensor */
|
|
#define OV6211_REG_ANALOGUE_GAIN CCI_REG16(0x350a)
|
|
#define OV6211_ANALOGUE_GAIN_MIN 1
|
|
#define OV6211_ANALOGUE_GAIN_MAX 0x3ff
|
|
#define OV6211_ANALOGUE_GAIN_STEP 1
|
|
#define OV6211_ANALOGUE_GAIN_DEFAULT 160
|
|
|
|
/* Test pattern */
|
|
#define OV6211_REG_PRE_ISP CCI_REG8(0x5e00)
|
|
#define OV6211_TEST_PATTERN_ENABLE BIT(7)
|
|
|
|
#define to_ov6211(_sd) container_of(_sd, struct ov6211, sd)
|
|
|
|
static const s64 ov6211_link_freq_menu[] = {
|
|
OV6211_LINK_FREQ_480MHZ,
|
|
};
|
|
|
|
struct ov6211_reg_list {
|
|
const struct cci_reg_sequence *regs;
|
|
unsigned int num_regs;
|
|
};
|
|
|
|
struct ov6211_mode {
|
|
u32 width; /* Frame width in pixels */
|
|
u32 height; /* Frame height in pixels */
|
|
u32 hts; /* Horizontal timing size */
|
|
u32 vts; /* Default vertical timing size */
|
|
u32 bpp; /* Bits per pixel */
|
|
|
|
const struct ov6211_reg_list reg_list; /* Sensor register setting */
|
|
};
|
|
|
|
static const char * const ov6211_test_pattern_menu[] = {
|
|
"Disabled",
|
|
"Vertical Colour Bars",
|
|
};
|
|
|
|
static const char * const ov6211_supply_names[] = {
|
|
"avdd", /* Analog power */
|
|
"dovdd", /* Digital I/O power */
|
|
"dvdd", /* Digital core power */
|
|
};
|
|
|
|
#define OV6211_NUM_SUPPLIES ARRAY_SIZE(ov6211_supply_names)
|
|
|
|
struct ov6211 {
|
|
struct device *dev;
|
|
struct regmap *regmap;
|
|
struct clk *xvclk;
|
|
struct gpio_desc *reset_gpio;
|
|
struct regulator_bulk_data supplies[OV6211_NUM_SUPPLIES];
|
|
|
|
struct v4l2_subdev sd;
|
|
struct media_pad pad;
|
|
|
|
struct v4l2_ctrl_handler ctrl_handler;
|
|
|
|
/* Saved register values */
|
|
u64 pre_isp;
|
|
};
|
|
|
|
static const struct cci_reg_sequence ov6211_400x400_120fps_mode[] = {
|
|
{ CCI_REG8(0x3005), 0x00 },
|
|
{ CCI_REG8(0x3013), 0x12 },
|
|
{ CCI_REG8(0x3014), 0x04 },
|
|
{ CCI_REG8(0x3016), 0x10 },
|
|
{ CCI_REG8(0x3017), 0x00 },
|
|
{ CCI_REG8(0x3018), 0x00 },
|
|
{ CCI_REG8(0x301a), 0x00 },
|
|
{ CCI_REG8(0x301b), 0x00 },
|
|
{ CCI_REG8(0x301c), 0x00 },
|
|
{ CCI_REG8(0x3037), 0xf0 },
|
|
{ CCI_REG8(0x3080), 0x01 },
|
|
{ CCI_REG8(0x3081), 0x00 },
|
|
{ CCI_REG8(0x3082), 0x01 },
|
|
{ CCI_REG8(0x3098), 0x04 },
|
|
{ CCI_REG8(0x3099), 0x28 },
|
|
{ CCI_REG8(0x309a), 0x06 },
|
|
{ CCI_REG8(0x309b), 0x04 },
|
|
{ CCI_REG8(0x309c), 0x00 },
|
|
{ CCI_REG8(0x309d), 0x00 },
|
|
{ CCI_REG8(0x309e), 0x01 },
|
|
{ CCI_REG8(0x309f), 0x00 },
|
|
{ CCI_REG8(0x30b0), 0x08 },
|
|
{ CCI_REG8(0x30b1), 0x02 },
|
|
{ CCI_REG8(0x30b2), 0x00 },
|
|
{ CCI_REG8(0x30b3), 0x28 },
|
|
{ CCI_REG8(0x30b4), 0x02 },
|
|
{ CCI_REG8(0x30b5), 0x00 },
|
|
{ CCI_REG8(0x3106), 0xd9 },
|
|
{ CCI_REG8(0x3503), 0x07 },
|
|
{ CCI_REG8(0x3509), 0x10 },
|
|
{ CCI_REG8(0x3600), 0xfc },
|
|
{ CCI_REG8(0x3620), 0xb7 },
|
|
{ CCI_REG8(0x3621), 0x05 },
|
|
{ CCI_REG8(0x3626), 0x31 },
|
|
{ CCI_REG8(0x3627), 0x40 },
|
|
{ CCI_REG8(0x3632), 0xa3 },
|
|
{ CCI_REG8(0x3633), 0x34 },
|
|
{ CCI_REG8(0x3634), 0x40 },
|
|
{ CCI_REG8(0x3636), 0x00 },
|
|
{ CCI_REG8(0x3660), 0x80 },
|
|
{ CCI_REG8(0x3662), 0x03 },
|
|
{ CCI_REG8(0x3664), 0xf0 },
|
|
{ CCI_REG8(0x366a), 0x10 },
|
|
{ CCI_REG8(0x366b), 0x06 },
|
|
{ CCI_REG8(0x3680), 0xf4 },
|
|
{ CCI_REG8(0x3681), 0x50 },
|
|
{ CCI_REG8(0x3682), 0x00 },
|
|
{ CCI_REG8(0x3708), 0x20 },
|
|
{ CCI_REG8(0x3709), 0x40 },
|
|
{ CCI_REG8(0x370d), 0x03 },
|
|
{ CCI_REG8(0x373b), 0x02 },
|
|
{ CCI_REG8(0x373c), 0x08 },
|
|
{ CCI_REG8(0x3742), 0x00 },
|
|
{ CCI_REG8(0x3744), 0x16 },
|
|
{ CCI_REG8(0x3745), 0x08 },
|
|
{ CCI_REG8(0x3781), 0xfc },
|
|
{ CCI_REG8(0x3788), 0x00 },
|
|
{ CCI_REG8(0x3800), 0x00 },
|
|
{ CCI_REG8(0x3801), 0x04 },
|
|
{ CCI_REG8(0x3802), 0x00 },
|
|
{ CCI_REG8(0x3803), 0x04 },
|
|
{ CCI_REG8(0x3804), 0x01 },
|
|
{ CCI_REG8(0x3805), 0x9b },
|
|
{ CCI_REG8(0x3806), 0x01 },
|
|
{ CCI_REG8(0x3807), 0x9b },
|
|
{ CCI_REG8(0x3808), 0x01 }, /* output width */
|
|
{ CCI_REG8(0x3809), 0x90 },
|
|
{ CCI_REG8(0x380a), 0x01 }, /* output height */
|
|
{ CCI_REG8(0x380b), 0x90 },
|
|
{ CCI_REG8(0x380c), 0x05 }, /* horizontal timing size */
|
|
{ CCI_REG8(0x380d), 0xf2 },
|
|
{ CCI_REG8(0x380e), 0x01 }, /* vertical timing size */
|
|
{ CCI_REG8(0x380f), 0xb6 },
|
|
{ CCI_REG8(0x3810), 0x00 },
|
|
{ CCI_REG8(0x3811), 0x04 },
|
|
{ CCI_REG8(0x3812), 0x00 },
|
|
{ CCI_REG8(0x3813), 0x04 },
|
|
{ CCI_REG8(0x3814), 0x11 },
|
|
{ CCI_REG8(0x3815), 0x11 },
|
|
{ CCI_REG8(0x3820), 0x00 },
|
|
{ CCI_REG8(0x3821), 0x00 },
|
|
{ CCI_REG8(0x382b), 0xfa },
|
|
{ CCI_REG8(0x382f), 0x04 },
|
|
{ CCI_REG8(0x3832), 0x00 },
|
|
{ CCI_REG8(0x3833), 0x05 },
|
|
{ CCI_REG8(0x3834), 0x00 },
|
|
{ CCI_REG8(0x3835), 0x05 },
|
|
{ CCI_REG8(0x3882), 0x04 },
|
|
{ CCI_REG8(0x3883), 0x00 },
|
|
{ CCI_REG8(0x38a4), 0x10 },
|
|
{ CCI_REG8(0x38a5), 0x00 },
|
|
{ CCI_REG8(0x38b1), 0x03 },
|
|
{ CCI_REG8(0x3b80), 0x00 },
|
|
{ CCI_REG8(0x3b81), 0xff },
|
|
{ CCI_REG8(0x3b82), 0x10 },
|
|
{ CCI_REG8(0x3b83), 0x00 },
|
|
{ CCI_REG8(0x3b84), 0x08 },
|
|
{ CCI_REG8(0x3b85), 0x00 },
|
|
{ CCI_REG8(0x3b86), 0x01 },
|
|
{ CCI_REG8(0x3b87), 0x00 },
|
|
{ CCI_REG8(0x3b88), 0x00 },
|
|
{ CCI_REG8(0x3b89), 0x00 },
|
|
{ CCI_REG8(0x3b8a), 0x00 },
|
|
{ CCI_REG8(0x3b8b), 0x05 },
|
|
{ CCI_REG8(0x3b8c), 0x00 },
|
|
{ CCI_REG8(0x3b8d), 0x00 },
|
|
{ CCI_REG8(0x3b8e), 0x01 },
|
|
{ CCI_REG8(0x3b8f), 0xb2 },
|
|
{ CCI_REG8(0x3b94), 0x05 },
|
|
{ CCI_REG8(0x3b95), 0xf2 },
|
|
{ CCI_REG8(0x3b96), 0xc0 },
|
|
{ CCI_REG8(0x4004), 0x04 },
|
|
{ CCI_REG8(0x404e), 0x01 },
|
|
{ CCI_REG8(0x4801), 0x0f },
|
|
{ CCI_REG8(0x4806), 0x0f },
|
|
{ CCI_REG8(0x4837), 0x43 },
|
|
{ CCI_REG8(0x5a08), 0x00 },
|
|
{ CCI_REG8(0x5a01), 0x00 },
|
|
{ CCI_REG8(0x5a03), 0x00 },
|
|
{ CCI_REG8(0x5a04), 0x10 },
|
|
{ CCI_REG8(0x5a05), 0xa0 },
|
|
{ CCI_REG8(0x5a06), 0x0c },
|
|
{ CCI_REG8(0x5a07), 0x78 },
|
|
};
|
|
|
|
static const struct ov6211_mode supported_modes[] = {
|
|
{
|
|
.width = 400,
|
|
.height = 400,
|
|
.hts = 1522,
|
|
.vts = 438,
|
|
.bpp = 8,
|
|
.reg_list = {
|
|
.regs = ov6211_400x400_120fps_mode,
|
|
.num_regs = ARRAY_SIZE(ov6211_400x400_120fps_mode),
|
|
},
|
|
},
|
|
};
|
|
|
|
static int ov6211_set_test_pattern(struct ov6211 *ov6211, u32 pattern)
|
|
{
|
|
u64 val = ov6211->pre_isp;
|
|
|
|
if (pattern)
|
|
val |= OV6211_TEST_PATTERN_ENABLE;
|
|
else
|
|
val &= ~OV6211_TEST_PATTERN_ENABLE;
|
|
|
|
return cci_write(ov6211->regmap, OV6211_REG_PRE_ISP, val, NULL);
|
|
}
|
|
|
|
static int ov6211_set_ctrl(struct v4l2_ctrl *ctrl)
|
|
{
|
|
struct ov6211 *ov6211 = container_of(ctrl->handler, struct ov6211,
|
|
ctrl_handler);
|
|
int ret;
|
|
|
|
/* V4L2 controls are applied, when sensor is powered up for streaming */
|
|
if (!pm_runtime_get_if_active(ov6211->dev))
|
|
return 0;
|
|
|
|
switch (ctrl->id) {
|
|
case V4L2_CID_ANALOGUE_GAIN:
|
|
ret = cci_write(ov6211->regmap, OV6211_REG_ANALOGUE_GAIN,
|
|
ctrl->val, NULL);
|
|
break;
|
|
case V4L2_CID_EXPOSURE:
|
|
ret = cci_write(ov6211->regmap, OV6211_REG_EXPOSURE,
|
|
ctrl->val << 4, NULL);
|
|
break;
|
|
case V4L2_CID_TEST_PATTERN:
|
|
ret = ov6211_set_test_pattern(ov6211, ctrl->val);
|
|
break;
|
|
default:
|
|
ret = -EINVAL;
|
|
break;
|
|
}
|
|
|
|
pm_runtime_put(ov6211->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const struct v4l2_ctrl_ops ov6211_ctrl_ops = {
|
|
.s_ctrl = ov6211_set_ctrl,
|
|
};
|
|
|
|
static int ov6211_init_controls(struct ov6211 *ov6211)
|
|
{
|
|
struct v4l2_ctrl_handler *ctrl_hdlr = &ov6211->ctrl_handler;
|
|
const struct ov6211_mode *mode = &supported_modes[0];
|
|
struct v4l2_fwnode_device_properties props;
|
|
s64 exposure_max, pixel_rate, h_blank;
|
|
struct v4l2_ctrl *ctrl;
|
|
int ret;
|
|
|
|
v4l2_ctrl_handler_init(ctrl_hdlr, 9);
|
|
|
|
ctrl = v4l2_ctrl_new_int_menu(ctrl_hdlr, &ov6211_ctrl_ops,
|
|
V4L2_CID_LINK_FREQ,
|
|
ARRAY_SIZE(ov6211_link_freq_menu) - 1,
|
|
0, ov6211_link_freq_menu);
|
|
if (ctrl)
|
|
ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
|
|
|
|
pixel_rate = ov6211_link_freq_menu[0] / mode->bpp;
|
|
v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_PIXEL_RATE,
|
|
0, pixel_rate, 1, pixel_rate);
|
|
|
|
h_blank = mode->hts - mode->width;
|
|
ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_HBLANK,
|
|
h_blank, h_blank, 1, h_blank);
|
|
if (ctrl)
|
|
ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
|
|
|
|
ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_VBLANK,
|
|
mode->vts - mode->height,
|
|
mode->vts - mode->height, 1,
|
|
mode->vts - mode->height);
|
|
if (ctrl)
|
|
ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
|
|
|
|
v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
|
|
OV6211_ANALOGUE_GAIN_MIN, OV6211_ANALOGUE_GAIN_MAX,
|
|
OV6211_ANALOGUE_GAIN_STEP,
|
|
OV6211_ANALOGUE_GAIN_DEFAULT);
|
|
|
|
exposure_max = (mode->vts - OV6211_EXPOSURE_MAX_MARGIN);
|
|
v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops,
|
|
V4L2_CID_EXPOSURE,
|
|
OV6211_EXPOSURE_MIN, exposure_max,
|
|
OV6211_EXPOSURE_STEP,
|
|
OV6211_EXPOSURE_DEFAULT);
|
|
|
|
v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov6211_ctrl_ops,
|
|
V4L2_CID_TEST_PATTERN,
|
|
ARRAY_SIZE(ov6211_test_pattern_menu) - 1,
|
|
0, 0, ov6211_test_pattern_menu);
|
|
|
|
if (ctrl_hdlr->error)
|
|
return ctrl_hdlr->error;
|
|
|
|
ret = v4l2_fwnode_device_parse(ov6211->dev, &props);
|
|
if (ret)
|
|
goto error_free_hdlr;
|
|
|
|
ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &ov6211_ctrl_ops,
|
|
&props);
|
|
if (ret)
|
|
goto error_free_hdlr;
|
|
|
|
ov6211->sd.ctrl_handler = ctrl_hdlr;
|
|
|
|
return 0;
|
|
|
|
error_free_hdlr:
|
|
v4l2_ctrl_handler_free(ctrl_hdlr);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void ov6211_update_pad_format(const struct ov6211_mode *mode,
|
|
struct v4l2_mbus_framefmt *fmt)
|
|
{
|
|
fmt->code = MEDIA_BUS_FMT_Y8_1X8;
|
|
fmt->width = mode->width;
|
|
fmt->height = mode->height;
|
|
fmt->field = V4L2_FIELD_NONE;
|
|
fmt->colorspace = V4L2_COLORSPACE_RAW;
|
|
fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
|
|
fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
|
|
fmt->xfer_func = V4L2_XFER_FUNC_NONE;
|
|
}
|
|
|
|
static int ov6211_enable_streams(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_state *state, u32 pad,
|
|
u64 streams_mask)
|
|
{
|
|
const struct ov6211_reg_list *reg_list = &supported_modes[0].reg_list;
|
|
struct ov6211 *ov6211 = to_ov6211(sd);
|
|
int ret;
|
|
|
|
ret = pm_runtime_resume_and_get(ov6211->dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Skip a step of explicit entering into the standby mode */
|
|
ret = cci_write(ov6211->regmap, OV6211_REG_SOFTWARE_RST,
|
|
OV6211_SOFTWARE_RST, NULL);
|
|
if (ret) {
|
|
dev_err(ov6211->dev, "failed to software reset: %d\n", ret);
|
|
goto error;
|
|
}
|
|
|
|
ret = cci_multi_reg_write(ov6211->regmap, reg_list->regs,
|
|
reg_list->num_regs, NULL);
|
|
if (ret) {
|
|
dev_err(ov6211->dev, "failed to set mode: %d\n", ret);
|
|
goto error;
|
|
}
|
|
|
|
ret = __v4l2_ctrl_handler_setup(ov6211->sd.ctrl_handler);
|
|
if (ret)
|
|
goto error;
|
|
|
|
ret = cci_write(ov6211->regmap, OV6211_REG_MODE_SELECT,
|
|
OV6211_MODE_STREAMING, NULL);
|
|
if (ret) {
|
|
dev_err(ov6211->dev, "failed to start streaming: %d\n", ret);
|
|
goto error;
|
|
}
|
|
|
|
return 0;
|
|
|
|
error:
|
|
pm_runtime_put_autosuspend(ov6211->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ov6211_disable_streams(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_state *state, u32 pad,
|
|
u64 streams_mask)
|
|
{
|
|
struct ov6211 *ov6211 = to_ov6211(sd);
|
|
int ret;
|
|
|
|
ret = cci_write(ov6211->regmap, OV6211_REG_MODE_SELECT,
|
|
OV6211_MODE_STANDBY, NULL);
|
|
if (ret)
|
|
dev_err(ov6211->dev, "failed to stop streaming: %d\n", ret);
|
|
|
|
pm_runtime_put_autosuspend(ov6211->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ov6211_set_pad_format(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_state *state,
|
|
struct v4l2_subdev_format *fmt)
|
|
{
|
|
struct v4l2_mbus_framefmt *format;
|
|
const struct ov6211_mode *mode;
|
|
|
|
format = v4l2_subdev_state_get_format(state, 0);
|
|
|
|
mode = v4l2_find_nearest_size(supported_modes,
|
|
ARRAY_SIZE(supported_modes),
|
|
width, height,
|
|
fmt->format.width,
|
|
fmt->format.height);
|
|
|
|
ov6211_update_pad_format(mode, &fmt->format);
|
|
*format = fmt->format;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ov6211_enum_mbus_code(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_state *sd_state,
|
|
struct v4l2_subdev_mbus_code_enum *code)
|
|
{
|
|
if (code->index > 0)
|
|
return -EINVAL;
|
|
|
|
code->code = MEDIA_BUS_FMT_Y8_1X8;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ov6211_enum_frame_size(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_state *sd_state,
|
|
struct v4l2_subdev_frame_size_enum *fse)
|
|
{
|
|
if (fse->index >= ARRAY_SIZE(supported_modes))
|
|
return -EINVAL;
|
|
|
|
if (fse->code != MEDIA_BUS_FMT_Y8_1X8)
|
|
return -EINVAL;
|
|
|
|
fse->min_width = supported_modes[fse->index].width;
|
|
fse->max_width = fse->min_width;
|
|
fse->min_height = supported_modes[fse->index].height;
|
|
fse->max_height = fse->min_height;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ov6211_init_state(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_state *state)
|
|
{
|
|
struct v4l2_subdev_format fmt = {
|
|
.which = V4L2_SUBDEV_FORMAT_TRY,
|
|
.pad = 0,
|
|
.format = {
|
|
.code = MEDIA_BUS_FMT_Y8_1X8,
|
|
.width = supported_modes[0].width,
|
|
.height = supported_modes[0].height,
|
|
},
|
|
};
|
|
|
|
ov6211_set_pad_format(sd, state, &fmt);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct v4l2_subdev_video_ops ov6211_video_ops = {
|
|
.s_stream = v4l2_subdev_s_stream_helper,
|
|
};
|
|
|
|
static const struct v4l2_subdev_pad_ops ov6211_pad_ops = {
|
|
.set_fmt = ov6211_set_pad_format,
|
|
.get_fmt = v4l2_subdev_get_fmt,
|
|
.enum_mbus_code = ov6211_enum_mbus_code,
|
|
.enum_frame_size = ov6211_enum_frame_size,
|
|
.enable_streams = ov6211_enable_streams,
|
|
.disable_streams = ov6211_disable_streams,
|
|
};
|
|
|
|
static const struct v4l2_subdev_ops ov6211_subdev_ops = {
|
|
.video = &ov6211_video_ops,
|
|
.pad = &ov6211_pad_ops,
|
|
};
|
|
|
|
static const struct v4l2_subdev_internal_ops ov6211_internal_ops = {
|
|
.init_state = ov6211_init_state,
|
|
};
|
|
|
|
static const struct media_entity_operations ov6211_subdev_entity_ops = {
|
|
.link_validate = v4l2_subdev_link_validate,
|
|
};
|
|
|
|
static int ov6211_identify_sensor(struct ov6211 *ov6211)
|
|
{
|
|
u64 val;
|
|
int ret;
|
|
|
|
ret = cci_read(ov6211->regmap, OV6211_REG_CHIP_ID, &val, NULL);
|
|
if (ret) {
|
|
dev_err(ov6211->dev, "failed to read chip id: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
if (val != OV6211_CHIP_ID) {
|
|
dev_err(ov6211->dev, "chip id mismatch: %x!=%llx\n",
|
|
OV6211_CHIP_ID, val);
|
|
return -ENODEV;
|
|
}
|
|
|
|
ret = cci_read(ov6211->regmap, OV6211_REG_PRE_ISP,
|
|
&ov6211->pre_isp, NULL);
|
|
if (ret)
|
|
dev_err(ov6211->dev, "failed to read pre_isp: %d\n", ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ov6211_check_hwcfg(struct ov6211 *ov6211)
|
|
{
|
|
struct fwnode_handle *fwnode = dev_fwnode(ov6211->dev), *ep;
|
|
struct v4l2_fwnode_endpoint bus_cfg = {
|
|
.bus_type = V4L2_MBUS_CSI2_DPHY,
|
|
};
|
|
unsigned long freq_bitmap;
|
|
int ret;
|
|
|
|
if (!fwnode)
|
|
return -ENODEV;
|
|
|
|
ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
|
|
if (!ep)
|
|
return -EINVAL;
|
|
|
|
ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
|
|
fwnode_handle_put(ep);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = v4l2_link_freq_to_bitmap(ov6211->dev, bus_cfg.link_frequencies,
|
|
bus_cfg.nr_of_link_frequencies,
|
|
ov6211_link_freq_menu,
|
|
ARRAY_SIZE(ov6211_link_freq_menu),
|
|
&freq_bitmap);
|
|
|
|
v4l2_fwnode_endpoint_free(&bus_cfg);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ov6211_power_on(struct device *dev)
|
|
{
|
|
struct v4l2_subdev *sd = dev_get_drvdata(dev);
|
|
struct ov6211 *ov6211 = to_ov6211(sd);
|
|
int ret;
|
|
|
|
ret = regulator_bulk_enable(OV6211_NUM_SUPPLIES, ov6211->supplies);
|
|
if (ret)
|
|
return ret;
|
|
|
|
gpiod_set_value_cansleep(ov6211->reset_gpio, 0);
|
|
usleep_range(10 * USEC_PER_MSEC, 15 * USEC_PER_MSEC);
|
|
|
|
ret = clk_prepare_enable(ov6211->xvclk);
|
|
if (ret)
|
|
goto reset_gpio;
|
|
|
|
return 0;
|
|
|
|
reset_gpio:
|
|
gpiod_set_value_cansleep(ov6211->reset_gpio, 1);
|
|
|
|
regulator_bulk_disable(OV6211_NUM_SUPPLIES, ov6211->supplies);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ov6211_power_off(struct device *dev)
|
|
{
|
|
struct v4l2_subdev *sd = dev_get_drvdata(dev);
|
|
struct ov6211 *ov6211 = to_ov6211(sd);
|
|
|
|
clk_disable_unprepare(ov6211->xvclk);
|
|
|
|
gpiod_set_value_cansleep(ov6211->reset_gpio, 1);
|
|
|
|
regulator_bulk_disable(OV6211_NUM_SUPPLIES, ov6211->supplies);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ov6211_probe(struct i2c_client *client)
|
|
{
|
|
struct ov6211 *ov6211;
|
|
unsigned long freq;
|
|
unsigned int i;
|
|
int ret;
|
|
|
|
ov6211 = devm_kzalloc(&client->dev, sizeof(*ov6211), GFP_KERNEL);
|
|
if (!ov6211)
|
|
return -ENOMEM;
|
|
|
|
ov6211->dev = &client->dev;
|
|
|
|
v4l2_i2c_subdev_init(&ov6211->sd, client, &ov6211_subdev_ops);
|
|
|
|
ov6211->regmap = devm_cci_regmap_init_i2c(client, 16);
|
|
if (IS_ERR(ov6211->regmap))
|
|
return dev_err_probe(ov6211->dev, PTR_ERR(ov6211->regmap),
|
|
"failed to init CCI\n");
|
|
|
|
ov6211->xvclk = devm_v4l2_sensor_clk_get(ov6211->dev, NULL);
|
|
if (IS_ERR(ov6211->xvclk))
|
|
return dev_err_probe(ov6211->dev, PTR_ERR(ov6211->xvclk),
|
|
"failed to get XVCLK clock\n");
|
|
|
|
freq = clk_get_rate(ov6211->xvclk);
|
|
if (freq && freq != OV6211_MCLK_FREQ_24MHZ)
|
|
return dev_err_probe(ov6211->dev, -EINVAL,
|
|
"XVCLK clock frequency %lu is not supported\n",
|
|
freq);
|
|
|
|
ret = ov6211_check_hwcfg(ov6211);
|
|
if (ret)
|
|
return dev_err_probe(ov6211->dev, ret,
|
|
"failed to check HW configuration\n");
|
|
|
|
ov6211->reset_gpio = devm_gpiod_get_optional(ov6211->dev, "reset",
|
|
GPIOD_OUT_HIGH);
|
|
if (IS_ERR(ov6211->reset_gpio))
|
|
return dev_err_probe(ov6211->dev, PTR_ERR(ov6211->reset_gpio),
|
|
"cannot get reset GPIO\n");
|
|
|
|
for (i = 0; i < OV6211_NUM_SUPPLIES; i++)
|
|
ov6211->supplies[i].supply = ov6211_supply_names[i];
|
|
|
|
ret = devm_regulator_bulk_get(ov6211->dev, OV6211_NUM_SUPPLIES,
|
|
ov6211->supplies);
|
|
if (ret)
|
|
return dev_err_probe(ov6211->dev, ret,
|
|
"failed to get supply regulators\n");
|
|
|
|
/* The sensor must be powered on to read the CHIP_ID register */
|
|
ret = ov6211_power_on(ov6211->dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = ov6211_identify_sensor(ov6211);
|
|
if (ret) {
|
|
dev_err_probe(ov6211->dev, ret, "failed to find sensor\n");
|
|
goto power_off;
|
|
}
|
|
|
|
ret = ov6211_init_controls(ov6211);
|
|
if (ret) {
|
|
dev_err_probe(ov6211->dev, ret, "failed to init controls\n");
|
|
goto power_off;
|
|
}
|
|
|
|
ov6211->sd.state_lock = ov6211->ctrl_handler.lock;
|
|
ov6211->sd.internal_ops = &ov6211_internal_ops;
|
|
ov6211->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
|
|
ov6211->sd.entity.ops = &ov6211_subdev_entity_ops;
|
|
ov6211->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
|
|
ov6211->pad.flags = MEDIA_PAD_FL_SOURCE;
|
|
|
|
ret = media_entity_pads_init(&ov6211->sd.entity, 1, &ov6211->pad);
|
|
if (ret) {
|
|
dev_err_probe(ov6211->dev, ret,
|
|
"failed to init media entity pads\n");
|
|
goto v4l2_ctrl_handler_free;
|
|
}
|
|
|
|
ret = v4l2_subdev_init_finalize(&ov6211->sd);
|
|
if (ret < 0) {
|
|
dev_err_probe(ov6211->dev, ret,
|
|
"failed to init media entity pads\n");
|
|
goto media_entity_cleanup;
|
|
}
|
|
|
|
pm_runtime_set_active(ov6211->dev);
|
|
pm_runtime_enable(ov6211->dev);
|
|
|
|
ret = v4l2_async_register_subdev_sensor(&ov6211->sd);
|
|
if (ret < 0) {
|
|
dev_err_probe(ov6211->dev, ret,
|
|
"failed to register V4L2 subdev\n");
|
|
goto subdev_cleanup;
|
|
}
|
|
|
|
/* Enable runtime PM and turn off the device */
|
|
pm_runtime_idle(ov6211->dev);
|
|
pm_runtime_set_autosuspend_delay(ov6211->dev, 1000);
|
|
pm_runtime_use_autosuspend(ov6211->dev);
|
|
|
|
return 0;
|
|
|
|
subdev_cleanup:
|
|
v4l2_subdev_cleanup(&ov6211->sd);
|
|
pm_runtime_disable(ov6211->dev);
|
|
pm_runtime_set_suspended(ov6211->dev);
|
|
|
|
media_entity_cleanup:
|
|
media_entity_cleanup(&ov6211->sd.entity);
|
|
|
|
v4l2_ctrl_handler_free:
|
|
v4l2_ctrl_handler_free(ov6211->sd.ctrl_handler);
|
|
|
|
power_off:
|
|
ov6211_power_off(ov6211->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void ov6211_remove(struct i2c_client *client)
|
|
{
|
|
struct v4l2_subdev *sd = i2c_get_clientdata(client);
|
|
struct ov6211 *ov6211 = to_ov6211(sd);
|
|
|
|
v4l2_async_unregister_subdev(sd);
|
|
v4l2_subdev_cleanup(sd);
|
|
media_entity_cleanup(&sd->entity);
|
|
v4l2_ctrl_handler_free(sd->ctrl_handler);
|
|
pm_runtime_disable(ov6211->dev);
|
|
|
|
if (!pm_runtime_status_suspended(ov6211->dev)) {
|
|
ov6211_power_off(ov6211->dev);
|
|
pm_runtime_set_suspended(ov6211->dev);
|
|
}
|
|
}
|
|
|
|
static const struct dev_pm_ops ov6211_pm_ops = {
|
|
SET_RUNTIME_PM_OPS(ov6211_power_off, ov6211_power_on, NULL)
|
|
};
|
|
|
|
static const struct of_device_id ov6211_of_match[] = {
|
|
{ .compatible = "ovti,ov6211" },
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, ov6211_of_match);
|
|
|
|
static struct i2c_driver ov6211_i2c_driver = {
|
|
.driver = {
|
|
.name = "ov6211",
|
|
.pm = &ov6211_pm_ops,
|
|
.of_match_table = ov6211_of_match,
|
|
},
|
|
.probe = ov6211_probe,
|
|
.remove = ov6211_remove,
|
|
};
|
|
|
|
module_i2c_driver(ov6211_i2c_driver);
|
|
|
|
MODULE_AUTHOR("Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>");
|
|
MODULE_DESCRIPTION("OmniVision OV6211 sensor driver");
|
|
MODULE_LICENSE("GPL");
|